Gubao

Home> Blog> What to do if the car screws loose

What to do if the car screws loose

September 24, 2021
In order to avoid the looseness of the car Screws, it is probably solved from the following points:
1. Spring washers should be flexible, well-sized spring Washers are convenient, the production cost is low, and they are widely used in automobiles. It is the use of the elastic deformation of the washer, so that the thread pair is axially tensioned, and the top of the oblique mouth of the washer also helps to prevent loosening. However, such gaskets lose their elasticity due to heat or prolonged tightening during use. Therefore, before the device Spring Washer, it should check whether the elasticity is not invalid. The way to look is to see if the top and bottom of the washer's interface are staggered by a certain point of view. If the misaligned point of view is small or not staggered, the washer has failed. The dimensions of the washer should correspond to the dimensions of the mating screw, and it is appropriate that the diameter of the washer be slightly smaller than the outer diameter of the nut.
types-washers (1)

2. The length of the split pin should be suitable if the connecting rod (head screw) of the engine connecting rod is loose, which will cause the loose bearing of the connecting rod, causing the abnormal sound of the engine and even the engine-related parts. Differentiated view of some connecting rod bearing abnormal sound problems, it is often found that the single connecting rod connecting Bolt on the locking nut clenching pin is now gone, the reason is mostly due to the long opening pin, high-speed movement and crank arm collision and breaking, Eventually drop. The method for determining the correct length of the split pin is to insert the split pin into the corresponding hole of the lock nut. After the hit with the hammer, the protruding length of the split pin does not exceed the plane of the crank arm, and then the split pin is locked as required. You can.

2

3. The device direction of the disc spring washer should be correct. The disc spring washer will not produce more scratches on the surface of the machine parts. Therefore, the use of the spring washer in the car is increasing, but if the device is not proper, it will not play. Avoid thread loosening effect. Because the second shaft oscillates forward and backward, the third gear jumps. The correct orientation of the device is probably to face the concave surface of the disc spring washer towards the adapter with the convex surface facing the nut. After the nut is tightened, the disc spring washer is deformed by force, and the supporting surface is subjected to a counter effect and the locking effect is obtained.


4, the correct direction of tightening the wire should be correct

Some parts of the automobile chassis (such as the connecting bolt of the shift fork and the shift fork shaft) use stable wire to avoid the looseness of the screw. It is often used to prevent the thread of the bolt set from loosening. It is more reliable to secure the wire against loosening, but the device should pay attention to the selection of the safe wire standard and the tightening direction after threading into the screw hole. The thick wire is not easy to pass through, the diameter should be slightly smaller than the diameter of the perforation, and there can be a slight resistance when crossing. The method of correct and correct wire penetration direction is: if a certain bolt is loosened, the stable wire is under tension, that is, loosening a bolt will tighten the adjacent two screws to correct; otherwise, Incorrect.

3

5. The locking plate should be locked on the side plane of the nut

Larger pieces of nut lock on the car often use locking pieces to prevent loose, such as the car steering knuckle lock nut, the second axis of the front end of the transmission lock nut. The locking of the locking piece shall be carried out after the nut has been tightened by a regular torque and then the locking piece is folded onto one of the side planes of the nut and hammered together to make it snap. Never lock the tab on the edge of the nut, this will not be an excellent anti-loose effect

car

Contact Us

Author:

Ms. Sally

Phone/WhatsApp:

+8618013112637

Popular Products
You may also like
Related Information
How to distinguish between stainless steel screws, galvanized and nickel-plated screws

At present, most of the screws are produced in Yongnian County, Hebei Province. Every county in the country has Yongnian who sells standard parts. Standard screws include bolts, screws, studs, nuts,...

Mechanical performance standards for common self-tapping screws and self-cutting self-tapping screws

First, the scope of application The SAE J933 standard specifies the mechanical and quality requirements for steel self-tapping screws for automotive and related industries. Not suitable for corrosion...

Sterling technology sharing: What are the differences between the three concepts of bolts, screws and screws?

In fact, the standard is that there are no screws and nuts. Screws are commonly known as "screws" with external threads. The shape of the nut is usually hexagonal, and the inner hole is internally...

Russia Releases New Standard for Wood Construction Screws and Male Screws

The Russian Timber Construction Association recently released a new standard for the design of connections for screws used in wood construction and externally threaded screws. The standard is also in...

Related Categories

Email to this supplier

Subject:
Email:
Message:

Your message must be betwwen 20-8000 characters

Related Products List

Home

Product

Whatsapp

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send